Controlling large weeds in Roundup Ready soybean fields

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

Controlling large weeds is often considerably more difficult than controlling smaller weeds. The following are some suggestions for controlling larger troublesome weeds in soybeans.

Marestail

Marestail has become one of our most troublesome weeds in no-till crop production, especially in soybeans. Marestail tend to be difficult to control even when the plants are small and in the rosette stage, but become even tougher when plants get more than 6 inches tall. That is why fall and early burndown treatments are critical to the long-term management of marestail. Unfortunately, that doesn’t always happen. In addition, there are populations of marestail that have developed glyphosate resistance in many areas.  However, some marestail populations are still susceptible to glyphosate, and even resistant plants are not completely immune to glyphosate.   

The most effective herbicide treatment for controlling marestail in Roundup Ready soybeans is probably a tank-mix of glyphosate plus FirstRate. The combination of the two herbicides seems to work better than either herbicide alone, even on resistant plants. It is important to use the full labeled rates of glyphosate and recommended adjuvants, including ammonium sulfate, to optimize control and help minimize the risk of developing more resistance. Other tank-mixes to consider with glyphosate for controlling marestail would include Classic and Synchrony herbicides. Unfortunately, some marestail may also be ALS resistant, in which case FirstRate, Classic, and Synchrony would also be fairly ineffective. This just further emphasizes the importance of early spring weed control. Liberty 280 herbicide has also provided fairly good control of large marestail as a burndown treatment or postemergence in Liberty Link soybeans. 

Velvetleaf

Velvetleaf has sometimes been difficult to control with glyphosate. There are no confirmed cases of glyphosate-resistant velvetleaf, but it is not extremely susceptible to glyphosate. Several application factors can affect control, including time of day, hard water, ammonium sulfate, and environmental conditions. Velvetleaf control with glyphosate can be optimized by using full rates of glyphosate and ammonium sulfate (17 lb/100 gal of spray), spraying during the daylight hours, and spraying when the plants are under minimal drought stress. Herbicide tank-mix partners with glyphosate that may enhance velvetleaf control would include Resource, Cadet, Marvel, FirstRate, Harmony, and Synchrony. 

Waterhemp and Palmer amaranth

These pigweed species used to be some of the most common weeds in soybean fields prior to Roundup Ready soybeans. Glyphosate applied early, and possibly again as a follow-up treatment was effective for many years, but because of the heavy reliance on glyphosate for weed control, glyphosate-resistant waterhemp has become fairly common in eastern Kansas and glyphosate-resistant Palmer amaranth has now been documented in several fields in central Kansas and appears to be rapidly increasing.

The best way to manage these pigweeds in soybeans is to use effective preemergence herbicides followed by postemergence treatment. However, if the preemergence herbicides weren’t applied or didn’t get activated in a timely manner, early-emerging pigweeds may not have been controlled and can grow-0000000000p wild. Flexstar, Cobra, Marvel, and Ultra Blazer can be fairly effective for controlling small pigweed, but are less effective as the pigweed gets larger, especially Palmer amaranth. These herbicides also provide some residual weed control, so tank-mixes of these herbicides with glyphsosate should be applied within 3 to 4 weeks after planting to optimize performance. Pursuit and Harmony were once fairly effective for pigweed control and can still provide good control of susceptible populations, but many fields now have ALS-resistant waterhemp and Palmer amaranth.   

Sunflower and Cocklebur

Fortunately, sunflowers and cocklebur are quite susceptible to glyphosate. However, these weeds are fast growing and often have multiple flushes of germination. It is important to use the full rate of glyphosate and get good spray coverage when trying to control larger sunflower and cocklebur. Tank-mixing Scepter or Classic herbicide with glyphosate may improve control and help provide residual control of later-emerging plants.

Conclusion

If weeds have gotten large, it’s always best to start with the highest labeled rate of glyphosate, with the proper adjuvants, and add other herbicides as needed, depending on the weed species present. In most fields, there will be a combination of one of more of the weeds listed above, so producers will have to see how the herbicide options match up and select the best combination.


Prev 1 2 Next All



Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...


Comments (0) Leave a comment 

Name
e-Mail (required)
Location

Comment:

characters left


HPC30A Belt Conveyor

The Patented HPC30A Belt Conveyor will unload lime, fertilizer, dirt or rock quickly (10 – 20 ton per minute lime ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form