Replanting soybeans: Variety selection, seed rate

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

Where soybean stands have been severely damaged or lost, producers may be thinking about replanting. The later it gets, the more difficult that decision becomes. With later-than-optimal planting dates, should producers make any changes in management strategies? Should a shorter-season variety be substituted as we move into late-June planting dates?

As planting is delayed, the situation begins to resemble doublecrop soybean production. The soybean crop following wheat is usually planted 2 to 6 weeks later than the optimum date for maximizing yields. Since planting is delayed, often until the end of June or early July, one is tempted to switch to a shorter-season variety to ensure the crop will mature before frost.

Although planting a late-maturing variety may increase the likelihood of frost damage, switching to a substantially earlier-maturing variety should be resisted. This is for two reasons:

1) Early-maturing varieties planted late in the season will usually have limited vegetative development (flowering earlier), short stature, and low yield potential.

2) Any variety will have fewer days to flowering, pod development, and maturity when planted late compared to earlier planting dates.

As planting dates get later into June, the day length has begun or will soon begin to shorten and nights will start getting longer. This change in photoperiod causes plant development to speed up. As a general rule, for every three days delay in planting, maturity is delayed by one day.

Since soybean development is hastened in later plantings, the highest yields in a late-planted or doublecropped system are often achieved by using the same variety, or one only slightly shorter in maturity, as what is used in full-season production. Sometimes a slighter later maturing variety is preferred for late or doublecrop plantings, just to encourage more canopy development before flowering.

Other management practices can be affected by late planting, however. Because late planting shortens the period for vegetative growth and reduces canopy development, increasing the seeding rate alone or in combination with narrow row spacing can help the crop compensate by providing the opportunity to produce more pods in the canopy.

Seeding rates can be increased by 30% to 50% in high-yielding environments if planting is delayed until late June or July. Although past research has demonstrated no consistent benefit for narrow row spacing (less than 30 inches) in Kansas, narrow rows may have an advantage in late plantings in the eastern half of the state.


Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...


Comments (0) Leave a comment 

Name
e-Mail (required)
Location

Comment:

characters left


Portable Conveyors

Convey-all portable conveyors are designed to handle your crops gently and efficiently. We offer an extensive line of high capacity ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form