Early season soybean diseases

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

This is another interesting year for soybean production and early season soybean diseases in Missouri. According to the Missouri Agricultural Statistics Service as of June 23, 2013, “soybeans were 84 percent planted which is 24 days behind last year but the same as normal. Emergence was 67 percent, 20 days behind last year and 5 days behind normal. Emergence was reported as uneven across the state.” Certainly weather has been a key factor in this. Unusually cold, wet conditions across most of the state delayed planting and have resulted in some uneven or poor stands.

Although weather is a key factor this season, soil-borne pathogens could still be contributing to some of the uneven stands and poor vigor in seedlings. A heavy rain event and slow emergence due to compaction could have given Pythium species an opportunity to attack developing seedlings. Plants which are struggling to send out roots and to survive could be targets for Rhizoctonia or Fusarium species. Plants with comprised root systems were more prone to desiccation from warm, drying winds during the recent spell of higher than normal temperatures. Some marginal browning of leaflets, wilting of plants and even premature death of plants may occur in drier areas of fields or across large areas of fields. Thus far this season Rhizoctonia seems to be the most prevalent problem.

Soybean seedling blights have the potential to cause losses in Missouri soybean fields every year. The specific seedling blights that occur and their severity vary with the environmental conditions each season. When checking stands this season, it is important to take into account soil conditions and environmental stress as well as checking for seedling diseases.

Pythium and Phytophthora are favored by wet conditions and are more likely to be serious problems when wet conditions exist at or just after planting. Rhizoctonia and Fusarium are not as restricted by soil moistures and soil temperatures but still need some moisture to initiate infection. Macrophomina phaseolina grows best at temperatures between 82-95°F. Infection of seedlings with Macrophomina is most likely to occur if conditions of high soil temperatures and low soil moisture exist during the first two to three weeks after planting.

Symptoms of Pythium damping-off range from seed rot or preemergence damping-off to early postemergence damping-off. Affected tissue develops a soft, watery brown rot. Pythium damping-off is most likely to occur in cool (50-550F), wet soils.

Phytophthora can cause seed rot, preemergence damping-off and early postemergence damping-off. Initially affected tissue develops a soft, watery brown rot. Within several days the affected plant parts may dry out and shrivel up becoming dark, dry and brittle. This early stage Phytophthora is difficult to distinguish from Pythium damping-off. Phytophthora can also cause a seedling blight in which established seedlings turn yellow, wilt and die. Generally the entire seedling is affected and roots may be poorly developed and rotted. Phytophthora root rot is more likely to occur in heavy, wet soils, low areas or compacted areas, but it may occur in light soils or better drained areas if heavy rains occur after planting.

Rhizoctonia can cause seedling blight and root rot of soybean. Affected stands may have an uneven appearance and seedlings appear pale green in color and stunted in growth. The identifying feature of this disease is a small, reddish lesion on one side of the stem at or just below the soil line. This lesion develops into a sunken, cankered area at the point of infection. Sometimes the lesion will expand to completely girdle the stem. On severely infected seedlings, the entire hypocotyl may be discolored and shriveled into a dry, stringy or wiry stem.

Fusarium can also cause root rot of soybean. Infection is usually confined to roots and lower stems. The lower part of the taproot and the lateral root system may be discolored, deteriorated or completely destroyed. General roots show a nondescript brown discoloration and a dry, shrunken rot. Above ground portions of plants may appear off-color and stunted. Plants with severe Fusarium root rot may die prematurely.

Charcoal rot, caused by Macrophomina phaseolina, may be more commonly recognized as a mid to late season disease on maturing soybean plants, but it can also occur early in the season on seedlings. Infected seedlings tend to show a reddish brown discoloration from the soil line up the stem. The discolored area changes from reddish brown to dark brown to black. Foliage may appear off color or begin to dry out and turn brown. If the growing point is killed, a twin stem plant may develop. Under hot, dry conditions, infected seedlings may die. Under cooler, wetter conditions, infected seedlings may survive but carry a latent infection. Then symptoms may reappear later in the season with hot, dry weather.

Once the crop has been planted, there is little that can be done to reduce incidence or severity of soybean seedling diseases. Additional stress from poor growing conditions, herbicide injury or other factors may compound problems with soybean seedling diseases. Prior to planting it is important to consider variety selection (especially in fields with a history of Phytophthora), fungicide seed treatment, crop rotation, seedbed preparation and conditions at planting.


Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...


Comments (0) Leave a comment 

Name
e-Mail (required)
Location

Comment:

characters left


Quickveyor

Made of high quality 304 stainless steel, the Quickveyor is one of the strongest trailers on the market. It’s belt ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form