Why planting soybean early improves yield potential

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

Last year, Jim Specht and Patricio Grassini, University of Nebraska agronomists, well documented that, on average, Nebraska farmers plant soybeans two weeks earlier than they did in 1980. In 1980, half the soybean crop was planted by May 25; in 2012, half the crop was planted by May 11. This trend to earlier planting is likely due to a number of factors, including: 

  • larger farm sizes that require an earlier start to planting to manage the volume of work;
  • increased use of herbicides which has allowed for more reduced tillage systems;
  • improved cold tolerance of soybean varieties coupled with seed treatments and climate change — soils warm up earlier than they used to (Pathak et al., 2012, see Figure 2),
  • improved planters that allow planting in more diverse situations, and
  • underlying all of this is education from UNL research and extension faculty that planting soybeans earlier improves yield potential. Soybean farmers listened and planted earlier.

Impacts of Earlier Soybean Planting

Early soybean planting results in:

  1. Plants reach V1 earlier in the season resulting in earlier flowering date (R1 growth stage) and potentially a longer growing season. Earlier R1, in turn, increases the length of the seed-fill period. Temperatures drive germination and seedling emergence until the V1 growth stage, i.e., when the first trifoliate has unrolled to the point where the leaflet edges are no longer touching. 
  2. Slower emergence in comparison to later-planted soybeans. Cooler soil temperatures slow hypocotyl elongation; however, this delay is not detrimental to productivity if plant populations aren't reduced to less than 90,000 plants per acre (see Rees, 2012). The most rapid emergence occurs with soil temperatures between 77°F and 95°F.
  3. More nodes per plant. When plants reach V1 earlier, they accrue more nodes during the growing season resulting in more potential pods and seeds per unit area. After V1, Nebraska research data clearly shows that nodes accrue at about 0.27 nodes per day, or, saying it another way, it takes 3.7 days to produce a new node.  Internode elongation is dependent on temperature; in contrast, node accrual is time dependent. Late-planted soybeans accrue fewer nodes than early-planted soybeans. Internode elongation slows after R3 — beginning pod — and effectively ceases at R5 as seed fill begins. Nodes continue to accrue until R5. Although drought stress does not affect the rate of node accrual, it does result in reaching R5 earlier, reducing node numbers and yield.
  4. Quicker canopy closure with earlier planting captures light earlier and, over the entire season, ensures full interception of solar radiation during the key stages for yield determination (pod set and seed fill). More light "harvested" results in an opportunity to achieve greater yield.
  5. Greater crop transpiration and less soil evaporation. Yield is linearly related to total transpiration. Early canopy closure reduces weed competition and evaporation from the soil surface and ensures more water available for crop transpiration.
  6. Similar yields regardless of row spacing. However, narrow rows may be of some advantage with very late planting - late May early June.
  7. Yield increases of 1/4 to 5/8 bushels per day for each day planting is moved closer to May 1 (Figure 1).


  1. Early-planted soybean attract early-emerging, overwintered bean leaf beetles (BLB). Although some leaflet feeding may occur, the major concern is that BLB transmit Bean Pod Mosaic Virus.
  2. Early-planted soybean may require a longer time to emerge than late-planted soybeans, depending on soil temperature and soil moisture. Dry soils at planting are not conducive to germination. 
  3. Water deficits later in the growing season inhibit growth and yield regardless of planting date.
  4. The extent of tillage and amount of residue cover affect soil temperatures. Although soil temperatures during the day don't vary as much with no-till as they do with other tillage systems,  early-season soil temperatures are cooler with no-till. Lower temperatures slow the germination process and thus lengthen the time to V1, potentially reducing yield.
  5. For the first 48 hours after planting both corn and soybean need soil temperatures near 50°F to avoid chilling injury during the rapid water imbibition stage. After the first 48 hours, these crops usually have minimal problems continuing the germination process at soil temperatures well-below 50°F — assuming temperatures remain above freezing; germination will be slower, of course, but if a seed fungicide treatment was applied, there should have be no concerns about loss of germinating seedlings.  Monitor your field's soil temperatures on the days preceding planting and on the day of planting plus your forecast temperatures for your area for the next 48 hours to estimate the likelihood of stable or increasing soil temperatures.

Prev 1 2 Next All

Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...

Comments (0) Leave a comment 

e-Mail (required)


characters left


Made of high quality 304 stainless steel, the Quickveyor is one of the strongest trailers on the market. It’s belt ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form