Six seedling pests that don’t need seed treatments

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

There are no major insect pests of soybean seedlings, but occasionally we do run into problems. Some folks use an insecticidal seed treatment in soybeans. While these products are effective to kill insects, they will not provide a yield benefit. To my knowledge, there has never been a single university field trial that showed a yield benefit to using an insecticidal seed treatment in any Southeastern state.

Tobacco thrips lives on both corn and cotton. Some of these thrips are resistant to some insecticidal seed treatments in the Midsouth. We can expect to drive resistance in our system if we use seed treatments where they aren’t needed. Let’s save the seed treatments for corn and cotton. Finally, insecticidal seed treatments don’t do anything for non-insects like slugs, deer, etc.

Here are some descriptions of injury you might encounter:

1. Thrips can pucker soybean leaves and silver them when densities are high. They will not cause a yield loss and no treatment is needed.

2. Bean leaf beetle is a pest that should be managed later in the season. It will almost never reach economic threshold in the early season for soybean.

3. Grasshoppers, katydids, and cutworms tend to be a problem on fields with lots of residue (think no-till) and fields that have not been properly rotated. They are also more of a problem on field edges. These should be controlled with a pyrethroid if they begin to reduce stand levels to densities below those recommended by NC Cooperative Extension (see adjacent graph).

4. Slugs, which are also more of a problem in no-till fields, are more difficult to control, as insecticides are ineffective. They are more of a problem when conditions are cool and wet. Slugs are difficult to sample, not only because of their small size, but because they are active in low light conditions, like cloudy days and at night. One thing that you can do is to move the residue around to find the slugs and to look for the slime of their trails where they have moved. The dried slime will shine in the sun.

Slugs will feed on the margins of plant leaves and once they have consumed this tissue, they can move to rasp and feed on terminals. Sometimes you will see chunks missing from the seedling stem where they have fed. In severe cases, slugs can consume entire seedlings.

The best management action to reduce slugs is to till. If you’re producing under no-till, slugs are probably not going to change your tillage practices. Basically the more trash you can clean away from the seedlings, the fewer problems you will have. Consider strip till. Less drastic steps are focusing on good residue removal with the row sweepers and using starter fertilizer. The only known remedial measure for slugs, besides waiting for warmer and dryer weather, is to use Deadline M-Ps (AMVAC).

5. Three-cornered alfalfa hoppers feed on seedling and are generally discovered after the fact, when plants lodge later in the season. Seed treatments and foliar pyrethroid sprays can effectively manage these insects. The problem is that it takes EXTREMELY high densities to impact yield. So your money is wasted 99.9% of the time targeting a seed treatment for these critters. In short, if you’ve had a problem with these in the past, do not waste your money with a seed treatment. Scout your beans and treat if you need to.

6. Finally, lesser cornstalk borer can give us problems, especially in late-planted soybeans, on droughty soils, and/or during hot and dry periods. Unfortunately we do not know of any remedial control measure (including pesticides) that is effective for this insect.

Prev 1 2 Next All

Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...

Comments (0) Leave a comment 

e-Mail (required)


characters left

Portable Conveyors

Convey-all portable conveyors are designed to handle your crops gently and efficiently. We offer an extensive line of high capacity ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form