Starter fertilizers and early-season nitrogen for wheat

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

To save time and cost, some wheat producers may be thinking about adding a little extra nitrogen (N) as urea or UAN to their phosphorus fertilizer through the drill with the seed. This would either be in addition to, or instead of, any preplant N applications.

While a minimum preplant N application of 20 to 40 lbs N per acre is often desirable, especially in no-till production systems, it is important to avoid placing urea containing fertilizers in direct seed contact. We suggest that NO urea or UAN solution be placed in contact with the seed. If the fertilizer N applied at seeding will be separated from seed by 1 inch or more, urea-containing fertilizers can be safely used.

Methods of early-season nitrogen applications

If the starter fertilizer can’t be “spiked” with urea to add extra N, how can the necessary 20 to 40 pounds of N be applied? Subsurface banding (knifing) of N as either anhydrous ammonia, liquid UAN, or dry product will result in the greatest N use efficiency by the wheat crop. This is especially true for no-till wheat production.

If knifed N applications are not used, the next best application method would be surface banding (dribbling) of UAN solution in streams on 15- to 18-inch centers. Broadcasting urea, ammonium nitrate, or UAN applications are not generally as efficient as subsurface banding, but they are often the best choice due to equipment, logistics, or weed management considerations. Broadcast applications of N will have the most consistent performance if followed by light incorporation, precipitation, or irrigation.

Direct seed placement of nitrogen

When placing starter fertilizer in direct contact with wheat seed, producers should use the following guidelines:

Suggested Maximum Rates of Fertilizer to be Applied Directly With Wheat Seed

 

 

Pounds N + K2O (No urea or UAN)

Row Spacing

(inches)

Medium to Fine

Textured Soils

Sandy or Dry

 Soils

15

16

11

10

24

17

6-8

30

21

The problem with placing urea-containing fertilizer with the seed is that urea is initially converted to ammonia and may be toxic to plant roots if the wheat seed is placed in direct contact with the fertilizer. Producers may hear of someone who has placed urea in direct seed contact and seemed to have no problems, but there are also many cases where urea-containing N fertilizers has injured the developing seedling and reduced or delayed emergence significantly. The risk of injury is greater in drier soils, at higher soil pH levels, and at higher N rates. High soil pH favors a higher concentration of ammonia as compared to ammonium as urea hydrolyzes. There is significant risk associated with placing urea-containing fertilizers in direct seed contact.

The chart below shows how soil texture affected the level of wheat germination when urea-N was applied with the seed in a K-State greenhouse study. The wheat was well watered in this study, but urea-N placed with the seed still reduced germination, especially in the sandy soil. The readings shown below were taken after 10 days. With the high rates of urea used in this study, it is possible that more damage to the seedlings would occur with time as the urea continues to hydrolyze into ammonia.

click image to zoomDorivar Ruiz Diaz, K-State Research and ExtensionFigure 1. Greenhouse study evaluating the effect of urea placed with the seed on germination. Plant counts 10 days after planting. Air seeders that place the starter fertilizer and seed in a band an inch or two wide, rather than a narrow seed slot, provide some margin of safety because the concentration of the fertilizer and seed is lower in these diffuse bands. In this scenario, adding a little extra urea containing N fertilizers to the starter less likely to injure the seed - but it is still a risk.

Blending DAP or MAP with the seed

What about blending dry 18-46-0 (DAP) or 11-52-0 (MAP) directly with the seed in the hopper? Will the N in these products hurt the seed? The N in these fertilizer products is in the ammonium-N form, not the urea-N form, and is much less likely to injure the wheat seed, even though it is in direct seed contact. As for rates, guidelines provided in the table above should be used. If DAP or MAP is mixed with the seed, the mixture can safely be left in the seed hopper overnight without injuring the seed or gumming up the works.

Although the response of wheat to these starter fertilizer products is primarily from the P, the small amount of N that is present in DAP, MAP, or 10-34-0 may also be important in some cases. If no preplant N was applied, and the soil has little or no carryover N from the previous crop, then the N from these fertilizer products could benefit the wheat, in addition to the P.

Dual placement of N and P

Dual-placement of N and P (anhydrous ammonia or UAN plus 10-34-0 applied in the same band below the soil surface) is a fertilizer application method usually used in preplant applications. Ammonium-N has long been known to increase P uptake by crops, and dual-placement can be very effective. Sometimes, producers will use this method at planting time, trying to position the band to the side of each row of wheat seed. Use caution, however.

If adequate separation of fertilizer and seed is accomplished, this is a good method of application that fits into many farmers’ overall no-till system. If adequate separation of the ammonia/UAN and seed is not accomplished, wheat germination/stand establishment can be severely affected.


Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...


Comments (0) Leave a comment 

Name
e-Mail (required)
Location

Comment:

characters left


Aluminum Grain Trailers

Maurer Manufacturing offers a complete line of high quality aluminum grain trailers. Manufactured in Spencer, Iowa, Maurer aluminum grain trailers ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form