Tips for anhydrous ammonia safety
Anhydrous ammonia (NH3) is a nitrogen crop fertilizer that can cause severe chemical burns; frostbite to the eyes, skin, and respiratory tract; and death. It is important for all individuals working with this type of fertilizer to understand the potential risks, necessary safety precautions, and proper response in the event of accidental contact.
Anhydrous ammonia is a hygroscopic compound, meaning that it takes up water from the nearest source, which can include the human body—especially the eyes, lungs, and skin because of their high moisture content. Anhydrous ammonia is caustic, corrosive, and damaging to tissue high in moisture content when it contacts the human body. Anhydrous ammonia inhalation incidents are typically severe because the victim's throat can swell shut, causing suffocation. When vapors or liquid come in contact with a person’s eyes, blindness may occur.
Typically, anhydrous ammonia is stored under pressure, but it vaporizes to a colorless gas. It has a unique odor that can be detected at a low concentration of 5 ppm. The concentration in fertilizer is approximately 1,000,000 ppm, but even brief exposure to a concentration of 2,500 to 6,500 ppm can result in death.
Anhydrous ammonia is transported under pressure as a liquid, so all equipment used for transport must be designed for use under high pressure to avoid ruptures or breaks. Incidents can occur when anhydrous ammonia escapes from transfer hoses or valves, equipment malfunctions and sprays anhydrous ammonia in multiple directions, hoses pull apart during transportation or application, and so on.
PPE and Supplies
It is essential that all workers who use anhydrous ammonia wear the appropriate personal protective equipment (PPE), be equipped with necessary response supplies, and know how to respond in an emergency. PPE should include ventless goggles or a full-face shield, rubber gloves with long cuffs that can be rolled to catch drips, and a long-sleeved shirt. Nonrubber gloves made of ammonia-proof material are acceptable. Because contact lenses can trap the gas and become fused to the eye, it is recommended that individuals not wear contact lenses while working with anhydrous ammonia.
In the event of an exposure emergency, the most important resource is an ample supply of clean water to begin flushing the eyes and skin. If you use a vehicle to transport anhydrous ammonia, you must carry a 5 gal. container of clean water. Each person working with anhydrous ammonia should carry a 6 to 8 fl. oz. squeeze bottle of water at all times for rapid response to an emergency.
Basic First Aid for Anhydrous Ammonia Exposure
The first-response treatment for anhydrous ammonia exposure is to flush the exposed area (skin, nose, throat, eyes, and so on) with clean water for a minimum of 15 minutes.
- Flush the exposed area immediately to decrease injury caused by the anhydrous ammonia coming in contact with skin or clothes. Although clean water is the ideal resource for flushing exposed areas of the body, if you do not have water available, other nontoxic liquids, such as cold coffee or orange juice, can be used.
- Remove contaminated clothing unless the clothing is frozen to the victim's skin.
- Seek medical attention immediately and inform medical staff of the exposure to anhydrous ammonia so that they will not treat the wounds with oils or ointments that can intensify the damage.
If you find a person who is in a continuous stream of anhydrous ammonia, contact your local emergency service responders or 911. Inform the emergency medical responders about the type of incident so they can bring the proper equipment to the scene. A self-contained breathing apparatus (SCBA) and protective clothing are necessary to remove a person from a continuous stream. Rescue workers will contact a hazardous materials (HAZMAT) disposal team if HAZMAT services are needed at the scene.
Note that these guidelines are not comprehensive, and all individuals working with anhydrous ammonia should receive training in the proper response to exposure emergencies.
Storage and Transportation
Anhydrous ammonia is a strong alkali that, when dissolved in water, readily reacts with copper, zinc, brass, and other alloys. Therefore, the only types of containers, fittings, and piping that should come in contact with anhydrous ammonia should be nongalvanized steel or iron. Do not store other materials, such as propane or liquefied petroleum gas, in a tank that has been used to store anhydrous ammonia.
When filling your anhydrous ammonia tank, do not fill it more than 85% full, and always disconnect the fill hose before moving the tank. Remember to bleed pressurized anhydrous ammonia from the hose before connecting or disconnecting the hose.
When transporting anhydrous ammonia, be sure to adhere to the following precautions and safety rules:
- Running Gear: Regularly inspect the wagon’s frame tongue, reach poles, anchor devices, wheel bearings, knuckles, ball joints, and pins for structural damage and wear and make necessary repairs and adjustments.
- Tires: Check tires for proper inflation, bald spots, and signs of wear and ensure that lug nuts are tight.
- Hoses and Valves: Inspect and replace hoses and valves as needed.
- The hydrostatic relief valve should be replaced every five years.
- The transfer hose should be replaced five years from the date of manufacture.
- Lubrication: Annually lubricate the wagon’s knuckle, wheels, tongues, and so on.
- Towing Vehicle: To increase the driver’s ability to control the towing vehicle, ensure that the towing vehicle weighs at least as much as the tank.
- A tractor can tow two tanks, but a truck can tow only one tank at a time.
- Speed Limit: When towing an anhydrous ammonia tank, observe a speed limit of 25 mph.
- Hitch Pin: Use a hitch pin with a safety chain when towing a tank wagon.
- Warning Lights: Ensure that the tank is equipped with a seven-terminal breakaway connector plug to properly operate turn signals, flashing warning lights, and a red brake light.
- Safety Signage: If operating on a highway, outfit the tank with all required safety markings, including a slow-moving vehicle (SMV) sign. (Click here for more information about SMV signs and increasing the visibility of your agricultural equipment.)
- The words Anhydrous Ammonia must appear on both sides of the tank and on the rear of the tank in letters 4 in. high. The words should be in contrast to the tank so that they can be read easily.
- Inhalation Hazard must appear on both sides of the tank in letters 3 in. high.
- A Department of Transportation (DOT) placard number 1005 for nonflammable gas should be placed on the front, back, and sides of the tank. click image to zoom
Additional Safety Recommendations
- Paint the tank with reflective white paint to decrease excessive pressure buildup that can occur when the tank is heated from direct sunlight.
- Do not use dented or damaged tanks until they have been checked by an authorized inspector and necessary repairs are completed.
- Allow only certified welders to perform welding on the tank.
- Regulations and codes regarding towing of anhydrous ammonia and signage may vary, so be familiar with and obey the regulations in your state
- Japan’s trade talks with U.S. to resume on Monday, gaps remain
- Dramatic warming to trigger surge in corn planting
- Ethanol: Bleak presence, brighter future
- Is there an advantage to more corn acres in your rotation?
- Drought maintains strangle-hold on southern Plains
- Oregon BEST funds semi-autonomous electric vehicle
- 2014 Farm Bill means big changes for agriculture
- Pop up fertilizers: What you need to know
- Ohio bill to require certification to apply fertilizer
- The boy is back? Risk of El Nino this year increases
- Monthly fertilizer prices: Comparing 2014 through 2009
- How to create promotions that attract ideal clients
- Commentary: Blame anti-GMO groups for deaths
- Julie Borlaug says biotech is necessary in fight against hunger
- What does “sustainable” food and agriculture really mean?
- Ohio bill to require certification to apply fertilizer
- Climate change will reduce crop yields sooner than we thought
- Carbon-dioxide hurts nitrogen assimilation by plants