P and K silage harvest of drought-damaged corn

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

The dry conditions this summer are resulting in quite variable corn growth and production potential. Some livestock producers are beginning harvest of corn damaged by drought conditions for silage. Corn silage harvest results in more phosphorus (P) and potassium (K) removal than grain alone because almost the entire plant is harvested. The increased amount removed with silage differs for P and K because the relative amount of P and K is different in corn vegetative parts than in grain. For P there can be approximately four times greater amount of P per ton of dry matter in grain than vegetative parts, but for K the opposite occurs, on average with almost three times greater amount of K per ton of dry matter in the vegetative parts.

The easiest approach for estimating P and K removal with silage harvest is to use existing estimates of the average corn silage removal amounts per unit of yield. From the ISU Extension and Outreach publication PM 1688 (A general guide for crop nutrient and limestone recommendations in Iowa), those values are 3.5 lb P2O5/ton and 8.0 lb K2O/ton (65 percent moisture based). On a dry matter basis, the values are 10 lb P2O5/ton and 23 lb K2O/ton. Of course the total removal amount per acre will vary according to the amount of silage harvested. These average concentration values could be correct with drought-damaged corn if the plant vegetation and grain are roughly affected in equal proportion.

However, drought conditions complicate estimates of P and K removal with silage harvested early because of largely unpredictable effects on dry matter production and nutrient uptake and accumulation. Depending on how moisture availability was during the season, there could be relatively more or less dry matter production than nutrient uptake, which would result in lower or higher concentration values, respectively. Data is very limited, however. Results from research in Kansas showed the nitrogen (N), P, and sulfur (S) concentrations were about the same for normal or drought-stressed corn, but the K concentration increased by about 50 percent.

An additional consideration is the growth stage of the corn when it is harvested. If the corn has not matured normally, but instead is harvested early or dies due to lack of moisture and high temperatures, it may really only be at an R1 (silking), R2 (blister), R3 (milk) or R4 (dough) growth stage at the time of silage harvest. In those cases, the full time period for nutrient uptake has not occurred and, in addition, the dry conditions could further reduce uptake. For each of those stages, and assuming little to no grain production, then the percent of normal full vegetative P and K uptake are for P: R1 50, R2 55, R3 55, R4 55 percent; and for K R1 75, R2 85, R3 85, R4 85 percent (adapted from ISU Extension and Outreach publication PMR 1009, Corn growth and development). Therefore, depending on the timing of the drought, the effects on P or K accumulation in the plant could differ greatly. Vegetative P and K concentration normally decrease as grain fill occurs due to translocation to grain, but that will be limited or non-existent in situations with little to no grain. One could multiply the percentage for the appropriate harvest growth stage by the normal P and K removal values for silage to estimate P2O5 and K2O amount per ton silage when there is little or no grain. For example, if silage is harvested at a R3 growth stage, then an estimated amount per ton silage (dry matter based) would be 10 x 0.55 = 5.5 lb P2O5/ton and 23 x 0.85 = 20 lb K2O/ton.

Because of the great deal of uncertainty, a more accurate estimate of P and K removal can be obtained by sending silage samples to a laboratory for analysis. The Iowa State University Soil and Plant Analysis Laboratory and all private laboratories are equipped to analyze plant tissue for P, K and other nutrients. You need to be sure the sample is representative by making a composite sample from material taken from different silage loads.

No matter the method used to estimate silage P and K concentration, the amount of silage harvested per acre has the greatest impact on nutrient removal. Therefore, it is important to have a good estimate of silage harvested and the moisture content.

For P and K, even if estimates of removal with silage harvest are off somewhat, soil sampling and testing in the fall can help with longer-term management in drought-affected fields. In extreme cases where no or very limited crop is harvested, then P and K will recycle from plants and be available for the next crop.

Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...

Comments (0) Leave a comment 

e-Mail (required)


characters left

LPV Seed Treater

The LPV Seed Treater has set a new standard boasting three configurable weighing methods for any-sized operation, a standard 42” ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form