Nitrogen rate adjustments for 2012 corn crop

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

Producers are asking Fabian Fernández, a University of Illinois assistant professor of crop sciences, about nitrogen rate adjustments for the 2013 corn crop.

He said that, in areas where corn yields were somewhat reduced but overall production practices were normal, no changes to regular practices should be needed for next year's crop. The Corn N Rate Calculator ( [3]) can be used to calculate the maximum return to nitrogen (MRTN) or profitable nitrogen rate range. For corn following soybean, even for fields with little or no yield, no changes to nitrogen-management decisions should be needed because soybeans do not leave excess nitrogen in the soil.

As a general rule, corn following soybean needs less nitrogen because the quantity and quality of the soybean residue reduces the amount of immobilization and increases the amount of nitrogen mineralization from crop residue and the soil. The Corn N Rate Calculator adjusts for this, showing that, compared to corn following corn, nitrogen rate for corn following soybean for the north, central, and south regions of Illinois can be reduced by approximately 50, 30, and 20 pounds of nitrogen per acre, respectively.

Decision making is more complicated for fields in which the drought severely affected the corn crop and the amount of nitrogen taken up was reduced. Probably, large amounts of unused nitrate-N are left in these fields. The problem is to determine how much of that nitrate is likely to be available next year.

Fernández said that, while there are no sure-fire methods, it is possible to estimate this amount. The indirect method is by determining how much nitrogen was removed in grain; the direct method is to measure soil nitrate-N (NO3-N) levels.

On average, a bushel of corn removes 0.66 pounds of nitrogen. To estimate the amount of remaining nitrogen, this removal rate is multiplied by the number of bushels produced per acre and subtracted from the amount of nitrogen applied per acre.

Not all that nitrogen will be plant-available in the next growing season. When nitrogen-loss potential is low (normal precipitation or drier conditions between harvest and next spring), 50 percent of the remaining nitrogen should be available for the 2013 crop.

For example, if a field received 180 pounds of nitrogen per acre and yielded only 70 bushels per acre, the remaining nitrogen is 180 minus 46 (multiply the 70 bushels times 0.66 to estimate the amount of nitrogen in the grain), which equals 134 pounds of nitrogen per acre. When the difference is multiplied by 0.5 (50 percent availability), the result is 67 pounds of nitrogen per acre to be subtracted from next year's nitrogen rate.

"The direct measurement using soil nitrate-N levels is, in my opinion, more reliable than the indirect measurement," Fernández said. "However, there is still a lot of uncertainty in the estimation because nitrogen availability for the 2013 crop will be largely a function of how much nitrogen-loss potential exists between fall and spring."

"To obtain a reliable measurement of nitrate-N, collect at least a 12-core composite from representative portions of the field, and at different positions with respect to the crop-row, to a depth of 2 to 3 feet," Fernández explained. "Keep each foot of sampling depth as a separate sample. The 2-foot depth should be adequate where little nitrate movement is expected, while the 3-foot depth is most appropriate for quantifying nitrate-N in fields where rain might have moved the nutrient deeper in the profile."

In any given year, there is nitrate present in the soil at the end of the growing season. Research has shown that for a 2-foot sample, only the amount above 40 pounds of nitrate-N per acre should be subtracted from the application rate.

Due to the uncertainty on how much carryover nitrogen will be present for the 2013 crop, the best way to adjust nitrogen rates may be to collect soil samples in the spring to adjust pre-plant or sidedress rates. This approach implies that nitrogen applications are done in the spring.

As with fall sampling, levels can vary across a field. To obtain a reliable measurement, use a sampling strategy that represents the field.

"In normal years, a 1-foot sample is recommended for spring samples, but with the present conditions, I would recommend that a 2-foot sample be obtained to quantify nitrate-N in the lower profile," Fernández advised.

Another approach that can be used to adjust nitrogen rates when the amount of carryover nitrogen is difficult to estimate is to choose the lower end of the profitable nitrogen-rate range in the Corn N Rate Calculator.

Finally, producers have asked Fernández about using the end-of-season lower corn stalk nitrate test to determine nitrogen rate adjustments for next year. "I do not recommend using this test. The values are likely to be artificially high because of the dry conditions that reduced plant growth and grain production," said Fernández.

Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...

Comments (0) Leave a comment 

e-Mail (required)


characters left

Smooth Wall Grain Bins

Meridian’s SmoothWall bins are the ultimate storage bins, used to handle and store fertilizer, grain, feed and seed, and extend ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form