Topdressing canola: How to maximize the benefits

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

To maximize the yield potential of winter canola, producers should topdress with nitrogen, sulfur, and possibly boron in the winter. Producers should be sure to make topdress applications under the right environmental conditions, with the right nutrients, and with the right application method.

Environmental conditions

The best time to topdress winter canola is during the rosette stage when the canola is dormant. Most years, this can easily be accomplished by topdressing in January or February, since temperatures are cold enough to keep canola from actively growing. If nitrogen is applied as a liquid when canola is green and physiologically active, be careful that the rate applied does not cause leaf burn. Both dry and liquid fertilizers are effective products.

Nutrients

A combination of nitrogen and sulfur, perhaps along with some boron, should be used in the topdressing blend.

Nitrogen. About two-thirds of the total nitrogen needed by the canola crop should be applied as a winter topdress. This should be done just as plants begin to show increased growth, and before the plants start to bolt. Topdress applications should be based on an updated assessment of yield potential, less profile residual nitrogen, and the amount of nitrogen applied in the fall. Suggested nitrogen rates for five yield levels and a soil with 2 percent organic matter and varying residual nitrate-nitrogen levels is shown in the table below. For soils with 1 percent organic matter, add 15 pounds nitrogen for each yield and nitrate level. For soils with 3 percent organic matter subtract 15 pounds nitrogen for each yield and nitrate level.

Total nitrogen fertilizer needs for canola as affected by yield potential and soil test nitrogen levels in the southern Great Plains

Profile N test (lbs/acre)

Yield potential (lbs/acre)

 

1,500

2,000

2,500

3,000

3,500

0

75

100

125

150

175

20

55

80

105

130

155

40

35

60

85

110

135

60

15

40

65

90

115

80

0

20

45

70

95

100

0

5

25

50

75

Source: Great Plains Canola Production Handbook, http://www.ksre.ksu.edu/bookstore/pubs/mf2734.pdf

Either solid or liquid forms of nitrogen can be used before green-up in the early spring. Once the weather warms and growth begins, solid materials are preferred for broadcast applications to prevent/avoid leaf burn.

Some of the new controlled-release products such as polymer-coated-urea (ESN) might be considered on very sandy soils prone to leaching, or poorly drained soils prone to denitrification. Generally a 50:50 blend of standard urea and the coated urea -- which will provide some N immediately to support bolting and flowering and also continue to release some N in later stages of development -- works best in settings with high loss potential.

Sulfur. If canola is deficient in sulfur, the consequences can be very serious because it needs sulfur to produce oil and protein in the seed. For this reason, soils having less than 20 lbs/acre sulfate-sulfur (10 ppm SO4-S) in the upper 24 inches should receive supplemental sulfur. A good rule to follow is to keep sulfur to nitrogen availability at a ratio of about 1 to 7. Another simple guideline is to apply 20 pounds sulfur per acre, which will be sufficient for low and medium yield levels. Sulfur can be applied in the fall and incorporated into the seedbed or surface applied with nitrogen in the winter topdressing. Canola growers may consider using elemental sulfur, ammonium sulfate, or a thiosulfate form of sulfur. Since elemental sulfur must oxidize to become plant available, it should only be applied in the fall. Ammonium thiosulfate or ammonium sulfate can be applied in the spring or fall, but thiosulfate should not be topdressed directly on tissue or placed with seed to avoid phytotoxicity.

Boron. If deficient, boron is one micronutrient that can have negative consequences on canola yield. Typically boron deficiency is not something we have seen in Kansas. However, if there are micronutrients that could influence yield, then boron would be one of them. The most important thing is to know what your soil sample states. Oklahoma State University is looking more into boron fertility. Applying boron may help to reduce flower abortion and enable efficient pod filling. However, there is not much room for error when comparing adequate boron fertility levels and toxic levels that might result from over application. Because of this, application rates of boron are often 1.0 lbs per acre or less. Soil and foliar applications of boron are effective. Foliar applications can be made with herbicides, and soil applied boron can be either broadcasted or banded. Make sure applications are uniform across the field to avoid toxicity.

Application method

It is important to avoid crushing winter canola with appli­cator tires after it bolts. Crushed plants will lodge and matu­rity will be delayed, which can slow harvest and increase the risk of shattering losses. For this reason, applicators with narrow tires are preferred. Do not use high flotation tires. As for the question of whether broadcast or banding is best -- if temperatures are cold and the plants are dormant, topdress fertilizer can be broadcast. If temperatures are mild enough that the canola plants have resumed active growth, it may be best to use streamer bars or some other form of banded application to avoid foliar burn.


Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...


Comments (0) Leave a comment 

Name
e-Mail (required)
Location

Comment:

characters left


Portable Conveyors

Convey-all portable conveyors are designed to handle your crops gently and efficiently. We offer an extensive line of high capacity ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form