Enhance yield through planting densities, N management

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

There is considerable interest in increasing corn yields with modern hybrids at higher than normal planting densities and adequate nitrogen (N) rates. In 2013, two hybrids, DKC48-12 and DKC49-94, both having insect and herbicide-stacked technology and improved drought tolerance capabilities, were tested at two row spacings of 20 inches and 30 inches with three population densities of 30,000, 36,000 and 42,000 plants per acre.

click image to zoom Two N rates of 120 pounds per acre and 240 pounds per acre were applied. The yield response of the two hybrids to row spacings and population rates was discussed in “Corn yield enhancement through planting densities and nitrogen management – Part 1.” In this article, the yield response to the third variable, the N rate, is discussed. Most of the N was applied as a sidedress injected using 28 percent liquid UAN on June 19, 2013.

click image to zoom Yield data from the two hybrids are summarized in Tables 1 and 2. Both hybrids produced highly significant yield increases at the high N compared to low N rate at all three populations. DKC48-12 had an average increase of 16 bushels per acre and DKCV49-94 had an average increase of 10 bushels per acre.

click image to zoom The 2013 growing season was dominated by excessive rainfall in April and June (Table 3) compared to an average year, delaying planting until May 20 and drowning out portions of the field in June. About one-third of June rainfall occurred after the June 19 N sidedress application. The wet and soggy conditions may have contributed to N losses due to denitrification and leaching.

The end of season cornstalk nitrate-N test was conducted on the two N rates (Table 4). The stalk nitrate-N level in the low N treatment was below the critical range of 700-2,000 ppm, indicating a potential N deficiency during the season. This N shortage may have reduced corn yield. The stalk nitrate-N level in the high N treatment was slightly above 2,000 ppm. It is possible, therefore, that the optimum N rate was between 120 and 240 pounds per acre. click image to zoom

This project was funded by Project GREEEN. I wish to thank the Dekalb/Asgrow staff at the Mason Technology Center for their collaboration with Michigan State University Extension and providing seed, equipment, and labor for this study.


Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...


Comments (0) Leave a comment 

Name
e-Mail (required)
Location

Comment:

characters left


Blend and Bulk Tower Systems

Waconia Towers provide speed, efficiency and reliability that only gravity-fed systems can offer. Towers are available with up to 300 ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form