Should UAN and residual herbicides be in a tank mix?

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

With the recent cold weather and varying degrees of injury growers are looking for ways to help their young corn recover. One potential concern is the application of urea ammonium nitrate (UAN) and residual herbicides in a tank mix.

UAN is a combination of urea and ammonium nitrate and has an N content of 28% to 32%. Under normal growing conditions, young corn can withstand some UAN without significant long-term damage. However, when corn is recovering from cold stress, it is probably better to find an alternative method of applying UAN.

The safest application method is to knife or band the UAN between the rows, but broadcast application is possible if the total nitrogen rate is kept to around 60 lb N per acre. An exact "safe" level of nitrogen is difficult to predict since environmental and corn plant conditions at application affect crop response. As described below, the amount of UAN needed to improve herbicide performance is much less than what is needed as a nitrogen source. Early leaf burn on corn usually is not a lasting problem since the growing point is still underground and a very small amount of total leaf area is exposed (Figures 1 and 2).

Herbicides

Early season weed control is imperative to maximize corn yield. Due to wet soil conditions, many corn growers were not able to apply residual, pre-emergence herbicides after corn planting but before corn emerged; however, several residual herbicides labeled in corn can be applied after corn emergence (See this CropWatch article).

Two important factors to consider when addressing weed control with residual herbicides applied after corn emergence are:

  1. tank mix partner and
  2. carrier options.

Applying herbicides and UAN at the same time in a tank mix for corn may seem like a good way to save time and a trip across the field; however, this enhances the foliar activity of herbicides and may result in significant foliar damage to young corn plants.

Several residual herbicides such as Degree Extra, Harness Extra, Keystone, and TripleFlex are labeled for preemergence application in corn with 28% UAN as a carrier option. However, it is not recommended that UAN be used as a carrier when Keystone and TripleFlex are being applied postemergence due to the potential corn injury.

Several other residual herbicides (Balance Flexx, Bicep II Magnum, Keystone, Lexar, Lumax, and TripleFlex) are labeled for early postemergence application in corn where UAN is NOT recommended. Postemergence application of these herbicides with UAN as a carrier will result in corn injury.

Degree Xtra is one of the few residual herbicides labeled for postemergence applications with UAN as a carrier; however, you should be aware of these aspects:

  • Temperature should not exceed 85°F within 24 hours of application.
  • Some leaf burn may occur.
  • Surfactants, crop oil, or other additives are not recommended unless specified.
  • See label for specific tank mix restrictions.

Some fertilizer salts, including UAN, can be used as herbicide additives in a small quantity to increase herbicide efficacy; however, this use would not supply much nitrogen relative to the total nitrogen requirement of the crop. A few herbicides, such as Python and Resolve DF, allow mixing UAN as a carrier at 2 quarts UAN per acre when applied after corn emergence; however, they cannot be applied with UAN as the total carrier because excessive corn injury may occur.


Prev 1 2 Next All



Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...


Comments (0) Leave a comment 

Name
e-Mail (required)
Location

Comment:

characters left


Declining Weigh Blending System

Ranco Declining Weigh (DW) is the standard in fertilizer blending because of the speed and accuracy of the blending process. ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form