Seeding depth of corn

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

Establishing uniform stands with plants that emerge at close to the same time will increase the probability of maximizing corn yields -- assuming fertility and pest issues are addressed and the weather cooperates. Deeper planting often has been mentioned as a way to increase uniformity of emergence.

A study conducted in 2011 at Manhattan examined the impact of planting depth on speed of emergence, stand uniformity, and yield. Two hybrids each were planted at six depths, from 1 inch to 3.5 inches, on April 11. The study was repeated with a planting on May 3. The two plantings provided very different soil temperatures. The average 2-inch soil temperature for the two weeks after planting on April 11 was 61°F and was 66°F after the May 3 planting. The two hybrids responded similarly so the results below are averages of both hybrids.

click image to zoom Timing of emergence

Figure 1 shows that the time it took for 90% of the plants to emerge increased by about two days for every additional inch of depth in the April 11 planting. The corn planted on May 3 all emerged within 7 to 9 days of planting, regardless of planting depth. Uniformity of emergence was greatest for the 1.5- and 2.0-inch planting depths with early planting and cooler soils. With later planting and warmer soils, emergence was most uniform for the 3.0-inch planting depth, but planting depth didn’t really cause much difference in timing of emergence compared to early planting.

click image to zoom Stand uniformity

Figure 2 shows that plant stands declined by about 1,500 plants per acre with each additional inch of planting depth in the April 11 planting. Planting depth did not influence final stands in the May 3 planting. Stand uniformity was greatest with the 1.5-inch planting depth in the April 11 planting and the 2.5-inch depth in the May 3 planting (Table 1). In this table, the lower the number of the standard deviation, the greater the uniformity of stand.

click image to zoom A number of irregular or deformed plants were noted in the April 11 planting, with a greater frequency occurring with the 3.0- and 3.5-inch depths (15% on average) compared to planting at 2.5 inches or less (3% on average). These deformations likely arose because plants at the deeper planting depths had to push leaves that were not protected by the coleoptile to the surface.

Although these plants were not tracked during the rest of the season, they likely contributed to non-uniform plant development within the stand.

click image to zoom Yield

Figure 3 shows that yield was similar for planting depths from 1.0 to 3.0 inches, but dropped off at 3.5 inches in the April 11 planting, likely related to the lower stands associated with that planting depth. Yields were highly variable in the May 3 planting due to conditions unrelated to planting depth (heat during silking, rooting depth), but did not change appreciably with planting depth. The 1.5 to 2.0 - inch planting depths resulted in some of the most consistent yields with both planting dates.


These results support current recommendations that corn be planted at 1.5 to 2.5 inches depending on soil conditions. Corn can be planted a bit deeper than 2.5 inches and shallower than 1.5 inches in certain conditions with a minimal impact on yield.

Prev 1 2 Next All

Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...

Comments (0) Leave a comment 

e-Mail (required)


characters left

Smooth Wall Grain Bins

Meridian’s SmoothWall bins are the ultimate storage bins, used to handle and store fertilizer, grain, feed and seed, and extend ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form