Evaluation of foliar fungicides on corn in 2011

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

The effect of foliar fungicides applied on foliar disease, stalk rot and yield of corn were evaluated during the 2011 growing season at six locations in Iowa: ISU Northwest Research and Demonstration Farm near Sutherland; ISU Northern Research and Demonstration Farm, Kanawha; ISU Northeast Research and Demonstration Farm, Nashua, Ames (central); ISU Southeast Research and Demonstration Farm near Crawfordsville; and the Armstrong Research and Demonstration Farm near Lewis (Fig. 1). Foliar fungicides were applied at various growth stages on corn (Table 1). Figure 1. Map of field locations where the 2011 corn fungicide study was done.

Materials and Methods
The experimental design at each location was a randomized complete block with four replications. Plot sizes were 10 foot-wide (four rows) by 35 to 100 foot long. Details on hybrid and planting, application and harvest dates are listed in Table 1. Fungicides were ground applied at either growth stage V5 to V6, R1 (silking), R2 (blister) or at both V5 to V6 and R1 at all six locations.

Foliar disease was assessed on the ear leaf and in the canopy above the ear leaf at R5 (dent) growth stage at the Nashua, Crawfordsville, Armstrong and Ames locations. Stalk rot was assessed at R6 (physiological maturity) at all locations except Sutherland. Plots were harvested with a plot combine. Grain moisture at harvest was determined and yields were converted to bushel per acre at 15.5 percent moisture. click image to zoom

Results
Foliar disease at R5 varied between locations (Table 2). 

  • At Crawfordsville, foliar disease severity was less than one percent and no treatment effects on disease severity were detected. 
  • The predominant disease at the Armstrong location was gray leaf spot which ranged from 0.66 to 8.8 percent severity on the ear leaf and 0.25 to 4.55 percent severity in the upper canopy. Applications of Headline Amp and Quilt Xcel at R1, and Headline + Headline Amp and Quadris + Quilt Xcel at V5+R1 significantly reduced disease severity. 
  • At Ames, gray leaf spot and northern leaf blight were present. Disease severity ranged from 2.6 to 9.8 percent. In general, applications of all fungicides applied at R1 or R2 reduced disease, although disease severity was not statistically different from the unsprayed check.
  • At Nashua, gray leaf spot was the predominant disease on the ear leaf (1.4 to 3.5 percent severity), while northern leaf blight was predominant in the canopy above the ear leaf (5.0 to 23.75 percent severity). Disease severity on the ear leaf and in the upper canopy was significantly lower than the unsprayed check for all fungicide applications, except for all product applications made at V5 alone.  An application of fungicide at R2 was most effective at reducing northern leaf blight in the upper canopy (5 to 7.5 percent versus 10.0 to 12.5 percent for an application at R1 versus 22.5 percent for the unsprayed check). 
  • Applications of fungicide made at V5 did not reduce foliar disease development during the R stages. Disease severity in V5 + R1 application treatments was similar to that of R1 application treatments.
  • Goss’s wilt was present in the upper canopy of some plots at the Ames and Armstrong locations.

Stalk rot severity was low (approximately 1 on the University of Illinois 1 to 5 scale) at all five locations where it was assessed. Treatment differences were detected only at the Armstrong location; stalk rot severity was significantly lower with applications of fungicide made at V5+R1 (0.0 to 0.35 versus 0.8 for the unsprayed check).

Seed moisture ranged from 14.4 to 20.5 percent depending on the location, but did not differ more than a few tenths of a percent amongst treatments within any location.

Yield varied across locations ranging from 156.7 to 229.6 bu/ac in the untreated control (Table 1). No differences in yield were detected between fungicide treatments and the untreated control at five of the six locations. At Armstrong, lower yields (P=0.08) occurred with some treatments than the unsprayed check.

Summary
Where foliar disease severity was moderate to high, all fungicide products successfully reduced disease when applied during early reproductive growth stages. Applications of fungicides made at V5 to V6 had no effect on foliar disease severity. Surprisingly low stalk rot disease occurred in the trial at all locations. There were no significant positive yield responses to fungicide applications. There was no justification in terms of reduced disease severity or yield response for double applications of fungicides made at V5 and R1.


Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...


Comments (0) Leave a comment 

Name
e-Mail (required)
Location

Comment:

characters left


Tube Series (TS) Conveyors

USC’s Tube Series Conveyors combine the gentleness of the signature Seed Series with the traditional stability of a tube-style conveyor, ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form