Green snap in corn

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

Some of the storms and extremely high winds this spring have caused significant stalk breakage in some corn fields. In these kinds of storms, it is not unusual to have up to 40 percent of stalks in some fields broken off at ground level. We see this type of damage somewhere every year. It is usually referred to as “green snap,” “brittle corn,” or “brittle snap.”

Green snap occurs when rapidly elongating corn stalks are subjected to high winds. Corn stalks are elongating rapidly between about V8 to tassel. Typically, corn is most susceptible to green snap in the two- or three-week period from late vegetative until silking. The stalks are growing rapidly and have enough height to catch more wind. These high winds will cause stalks to break in the section close to the lower nodes.

A number of factors can affect the severity of green snap. Anything that contributes to rapid, vigorous growth may make corn more susceptible to this problem. Such contributing factors include high nitrogen fertilizer rates, rotation after soybeans, higher plant densities (promoting early competition and elongation, and thinner stalks) and early planting. Unfortunately, these are all recommended best management practices for corn production.

click image to zoomIgnacio CiampittiFigure 1. Corn showing effects of wind damage, “green snap,” early during the vegetative period. Timing has a huge impact on the severity of green snap, with much less damage usually evident in younger corn (Figure 1) or in fields that have tasseled and silked. The factor that can be addressed most readily is hybrid selection. Although no hybrid is immune to the problem, some hybrids are more susceptible to green snap than others.

What are the implications of all those broken plants for the current crop? Damaged plants are broken completely in two, so there is no hope for recovery. Even so, the yield loss in an affected field usually will be much less than the stand loss. Before tasseling, surviving corn plants can respond to the additional resources made available by the removal of damaged plants by maintaining larger ears or setting additional ears, or increasing final kernel weight. With 10% or fewer broken stalks, it may be hard to detect a significant yield loss if stands were adequate before the storm.

click image to zoomKraig RoozeboomFigure 2. Green snap in corn at a later, more vulnerable vegetative stage of growth. Yield losses will increase with “patchy” stand losses because surviving plants are too far apart to compensate for lost plants. If large patches are damaged, or if stand losses are significant, there may still be an opportunity to cut the worst areas with a swather or crimper to salvage some forage if it can be utilized. It is not too late to plant sunflower, soybeans, or grain or forage sorghum if the stand is a total loss, depending upon the herbicide program used on the damaged corn crop.


Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...


Comments (0) Leave a comment 

Name
e-Mail (required)
Location

Comment:

characters left


Declining Weigh Blending System

Ranco Declining Weigh (DW) is the standard in fertilizer blending because of the speed and accuracy of the blending process. ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form