Putting insecticide out with foliar fungicides?

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

As much of our corn begins to tassel, some questions have predictably been asked about putting insecticide out with foliar fungicide applications. This is NOT a generally recommended practice. Myself and my counterparts have tested this thoroughly in the Mid South, and these data indicate a negative return on investment in most cases. Below are some points (and exceptions) for your consideration.

What pest are you targeting? I often get no answer when I ask this question. One common insect mentioned is Japanese beetle. However, our very recent research indicates this is a borderline non-pest unless very high numbers (3 or more per ear) occur during the first week of pollination. It is rare to find an average of 3 beetles per ear, except perhaps on field edges. I encourage you to test this yourself. Flag some ears where Japanese beetles have ‘gone to town’ on the silks. Go back and look at these ears later.

Another target mentioned is corn earworm. Decades of research has shown that it is not feasible to control corn earworm feeding in ears with a single insecticide application. Our recent data shows that kernel injury can not be reduced by a single insecticide application when corn earworm pressure is high … you kill one and another takes its place. I’ve had a few tests where a single application of at least some insecticides has reduced kernel injury IF relatively low numbers of corn earworms are present. Even then, this has often been a short term phenomenon that largely disappears as other larvae infest ears. And even in these circumstances, this has not translated into a yield increase. Some of the newer Bt corn traits are pretty good at reducing kernel injury. However, I’ve not been able to demonstrate that this has increased yield. Recent research indicates that much of this kernel damage is to small kernels in the ear tip that never would have made it into the combine. Furthermore, our data suggests that undamaged kernels in the ear can compensate for this injury.

The exception to all of this is treating non-Bt when corn borers are present. This is why it is important to use southwestern corn borer (SWCB) pheromone moth traps to gauge the level of risk in your fields. I’ve had many experiences where a single insecticide application to non-Bt corn has significantly increased yield when SWCB are present at treatment level. Populations tend to be low in many areas of the state, partly due to the widespread use of Bt corn. Frankly, most areas don’t really have a problem. Populations of SWCB are also relatively low this year, likely due to the hard winter. I previously discussed UT thresholds for this pests (http://news.utcrops.com/2014/06/southwestern-corn-borer-and-corn/). Another point to consider is that, as typically occurs around first tassel, moth traps indicate that we are between generations of SWCB. I do not expect the second generation to begin in earnest for 2-3 weeks. Pyrethroid insecticides should certainly not be expected to provide more than a week of residual control (and less if it rains).

I hate to ruin the party, but you should have a better reason to spray insecticides than “I’m going over the field anyhow” or “it really doesn’t cost that much”. Besides the added cost, there is baggage from making unnecessary pesticide applications including potentially flaring secondary pests such as spider mites, selection for insecticide resistance, and potential negative environmental impacts. Have a reason, not excuses!

Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...

Comments (0) Leave a comment 

e-Mail (required)


characters left


Made of high quality 304 stainless steel, the Quickveyor is one of the strongest trailers on the market. It’s belt ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form