Disease problems in Nebraska corn

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

A number of diseases have been reported and/or confirmed in corn samples from around the state. Weather conditions continue to be favorable for many diseases. Producers and consultants should monitor the severity of these and other diseases and their potential for impacting yield to assess the need for treatment.

Leaf Diseases Caused by Fungi: Northern Corn Leaf Blight

Northern corn leaf blight (NCLB) has been confirmed in several fields in eastern Nebraska.  Warm humid weather favors infection by the fungus, Exserohilum turcicum, which causes this disease. Weather conditions, including cloudy days, moderate temperatures (64-81°F), high humidity and frequent rainfall will favor further infection and spread of this and other fungal pathogens that survive in infected corn residue from recent years.

Like most other diseases caused by pathogens in plant residue, lesions may develop on the lower leaves first and continue to develop on leaves higher up the plant as long as conditions are favorable. NCLB tends to have larger, cigar-shaped lesions (Figure 1) with rounded ends. These lesions can be confused with Goss's bacterial blight lesions. Fungal spores may develop on NCLB lesions making them appear darker and/or dusty.

Management

Development and spread of NCLB prior to tasseling could reduce corn yield, particularly as lesions develop and expand, killing leaf area that's necessary for grain fill later. It is most important to protect leaves at the ear leaf and above that contribute the most to grain fill. In some fields, the disease has already reached leaves 4-6.

With the early development of NCLB now, it may be necessary to apply a foliar fungicide to slow disease spread and protect uninfected leaf tissue in affected fields. Lesion development requires up to two weeks after infection occurs. Thus, it is possible that one to two leaves are already infected above the highest leaf on the plant that has recognizable lesions. To determine if a fungicide application is economical for you, consider the price of corn, yield potential, cost of treatment, and disease severity.

No treatment thresholds have been established for NCLB. However, you can assess your risk for developing yield-limiting disease severity by considering the high risk factors listed below. Having more of these risk factors will increase the likelihood of increasing severity of NCLB and getting a return on the cost of a fungicide application:

  • Poor hybrid disease rating(s) for NCLB (consult seed catalog or company representatives for ratings)
  • Pre-tassel growth stage
  • Continuous corn
  • History of NCLB
  • Substantial corn residue
  • Humid/wet weather forecast

Scout fields now and frequently to monitor for development of NCLB and other diseases. In fields currently affected by NCLB, it will be important to consider this disease in the future when making hybrid selections and other management decisions, especially crop rotation, tillage, etc.

For more information see the UNL video, Corn Diseases: Northern Corn Leaf Blight  and the Purdue University publication, Diseases of Corn: Northern Corn Leaf Blight (BP-84-W).

Bacterial Diseases Continue

Bacterial diseases in corn continue to be confirmed and reported in fields around the state, especially in fields where corn was wounded during recent inclement weather. In particular, Goss's bacterial wilt and blight, bacterial stalk rot and bacterial leaf streak have all been confirmed.  Current moderate to warm weather conditions will continue to support spread and development of these diseases.

Symptoms:

Affected corn may have one or more of the following symptoms:

  • water-soaked lesions,
  • wilting,
  • discoloration,
  • internal decay, and
  • sometimes unpleasant odor.

Systemically infected plants often will be discolored inside the stems. Other symptoms on the leaves may appear somewhat different than the classic leaf blight symptoms usually observed with Goss's wilt, such as the dark freckles near the edges of lesions. Glossy exudate may be visible on the surface of leaves and is common in plants with Goss's wilt, but may occur with some other bacterial diseases, too. Since the pathogens causing these diseases are at least somewhat common in fields, it is possible for plants to have more than one disease.

Unfortunately, there is no foliar treatment recommended for Goss's wilt or other bacterial diseases at this point. Since several diseases may appear similar, it is necessary to submit a sample(s) for diagnosis and confirmation.


Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...


Comments (0) Leave a comment 

Name
e-Mail (required)
Location

Comment:

characters left


Tube Series (TS) Conveyors

USC’s Tube Series Conveyors combine the gentleness of the signature Seed Series with the traditional stability of a tube-style conveyor, ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form