Tips for ‘late’ applications of nitrogen

decrease font size  Resize text   increase font size       Printer-friendly version of this article Printer-friendly version of this article

Persistent rains this year may force many growers to sidedress their nitrogen (N) in corn this year much later than what is considered normal. Other growers may be supplementing their earlier N applications to replace N lost from denitrification and leaching.

The following are some suggestions from extension soil fertility specialists at Ohio State and Purdue University from past years that address various questions concerning N applications to corn after planting.

How Late can N be Applied? 

Corn utilizes large quantities of N during the grand growth stage. From the 8 leaf stage through tasseling N uptake is 4 to 8 pounds per day. For most corn hybrids N uptake is complete shortly after pollination. So, most of the N should be applied prior to the 10 leaf stage, with any supplemental applications complete by or shortly after tasseling. Under conditions of severe N deficiency, some response would be expected to low rates of N (30 to 60 pounds) as late as three weeks after pollination.

What is the Best N Source to Use? 

Ammonia or N solutions knifed in are preferred in most situations, especially high residue fields. Granular urea can also be applied over the top in clean tilled situations, but those applications can be risky if rainfall does not come shortly after application. Urea stabilizers (Agrotain) should be considered in high residue situations. Granular urea broadcast in standing corn will cause some foliar burn when granules fall into the whorl. While it may appear unsightly, little yield decrease normally occurs if the fertilizer is applied prior to the 10-leaf stage.

How Much N Should Be Applied?

If the corn has gotten too tall to sidedress by this point (mid to late June), it has probably not been severely stressed and yield potential is still good. An example would be rotation corn after beans which had some starter or 28% applied with herbicides with good green color. Nitrogen rates should approach what was initially planned at the beginning of the season. Research at Ohio State shows that decreased rates can do well, but do not decrease rates by more than 10-15%.

Can I Broadcast 28-0-0 Solutions "Over the Top?"

Using broadcast applications of 28% N solution to sidedress N will cause some burn to foliar tissue of corn plants.

The severity of injury is determined by the plant’s stage of growth, the amount of N used and form of N. If the plant growing point is at or below the soil surface (or when plant has six collared leaves or less), the extent of foliar injury caused by burn will usually be negligible if the N rate is kept below 50 lb/acre. Even with higher N rates at later vegetative growth stages the injury from leaf burn is normally not so severe that it outweighs the potential benefits received from the N addition. The degree of plant burning is less with urea granules than with other N products.

Dribbling 28% solution with drop nozzles as a narrow band on the soil surface is an alternative approach that can help reduce foliar burning. Dribbling 28% is also a more efficient use of N than broadcast surface application because it helps reduce N volatilization. Urea stabilizers may be considered for this application, but tillage is a major deciding factor on whether or not they are necessary. High residue corn fields may benefit from urea stabilizers, but low residue fields are less likely to benefit. At this point of the growing season, and the need for plenty of nitrogen by the crop, we do not recommend nitrification inhibitors. We also rarely see positive responses to nitrification inhibitors when N is sidedressed.

Can I Apply N to Every Other Row?

Research in Indiana, Illinois and Iowa has all shown that farmers can knife ammonia or N solutions in every other row middle (60 vs. 30 inch spacing) with no reduction in yield. The only caution is that extra attention must be paid, especially in wet conditions, that no knives plug with soil. A plugged knife in 60 inch spacing gives 4 rows with no N and will seriously reduce yields.


Prev 1 2 Next All



Buyers Guide

Doyle Equipment Manufacturing Co.
Doyle Equipment Manufacturing prides themselves as being “The King of the Rotary’s” with their Direct Drive Rotary Blend Systems. With numerous setup possibilities and sizes, ranging from a  more...
A.J. Sackett Sons & Company
Sackett Blend Towers feature the H.I.M, High Intensity Mixer, the next generation of blending and coating technology which supports Precision Fertilizer Blending®. Its unique design allows  more...
R&R Manufacturing Inc.
The R&R Minuteman Blend System is the original proven performer. Fast, precise blending with a compact foot print. Significantly lower horsepower requirement. Low inload height with large  more...
Junge Control Inc.
Junge Control Inc. creates state-of-the-art product blending and measuring solutions that allow you to totally maximize operating efficiency with amazing accuracy and repeatability, superior  more...
Yargus Manufacturing
The flagship blending system for the Layco product line is the fully automated Layco DW System™. The advanced technology of the Layco DW (Declining Weight) system results in a blending  more...
Yargus Manufacturing
The LAYCOTE™ Automated Coating System provides a new level of coating accuracy for a stand-alone coating system or for coating (impregnating) in an automated blending system. The unique  more...
John Deere
The DN345 Drawn Dry Spreader can carry more than 12 tons of fertilizer and 17.5 tons of lime. Designed to operate at field speeds up to 20 MPH with full loads and the G4 spreader uniformly  more...
Force Unlimited
The Pro-Force is a multi-purpose spreader with a wider apron and steeper sides. Our Pro-Force has the most aggressive 30” spinner on the market, and is capable of spreading higher rates of  more...
BBI Spreaders
MagnaSpread 2 & MagnaSpread 3 — With BBI’s patented multi-bin technology, these spreaders operate multiple hoppers guided by independent, variable-rate technology. These models are built on  more...


Comments (0) Leave a comment 

Name
e-Mail (required)
Location

Comment:

characters left


Fertilizer Conveying Systems

Waconia Manufacturing routinely designs receiving systems for volume requirements from 60 to 1,500 TPH. All receiving systems are fabricated with ... Read More

View all Products in this segment

View All Buyers Guides

Feedback Form
Feedback Form